<tr id="tnogj"><track id="tnogj"></track></tr>
  • <output id="tnogj"></output>

    <ins id="tnogj"><video id="tnogj"><var id="tnogj"></var></video></ins>

  • <tr id="tnogj"><small id="tnogj"></small></tr>
    <ruby id="tnogj"><option id="tnogj"><del id="tnogj"></del></option></ruby>

    <noscript id="tnogj"></noscript>

    1. <ins id="tnogj"><video id="tnogj"><optgroup id="tnogj"></optgroup></video></ins>
      1. <tr id="tnogj"></tr>
        <noframes id="tnogj"><small id="tnogj"></small></noframes>

          <code id="tnogj"></code>

            <code id="tnogj"></code>
            <sup id="tnogj"><small id="tnogj"></small></sup>

            1. <ins id="tnogj"><acronym id="tnogj"></acronym></ins>

                  <kbd id="tnogj"><video id="tnogj"></video></kbd>
                  聯系我們
                  聯系人:xx
                  轉讓電話:13313028229
                  地址:xx
                  新聞動態
                  瀝青路面快速修補方法
                  坑槽清理
                  Pit cleaning
                  確定坑槽開挖位置,四周銑刨或切縫后,將待修補的坑槽內及四周的碎石、廢渣清理干凈,坑槽內不得存有泥漿,冰塊等雜物,被修補的坑槽應有整齊的切邊,廢渣的清除要見到固體堅固面為止。
                  Determine the excavation location of the pit, after milling or cutting around, clean up the gravel and waste residue in and around the pit to be repaired. No slurry, ice and other debris can be stored in the pit. The repaired pit should be trimmed neatly, and the removal of waste residue should see solid surface.
                  刷涂界面劑
                  Brushing Interface Agent
                  在清理好的坑槽四周及底部刷涂界面劑,尤其是坑槽四周要涂刷均勻。這樣新舊料粘合效果會更好。如果瀝青路面坑槽修補,清理干凈也可也不涂刷,根據實地情況而定。
                  Brush the interface agent around and at the bottom of the cleared pit, especially around the pit. In this way, the bonding effect of new and old materials will be better. If the pit of asphalt pavement is repaired, it can be cleaned and not painted, depending on the actual situation.
                  冷補料填滿坑槽
                  Filling pit with cold filling material
                  把足夠的華通冷補料填進坑槽內,直到填料高出路面l1.5cm左右,填滿后坑槽中央處應稍高于四周路面并呈弧形,若路面坑槽深度大于7cm時,應分層填補,逐層壓實,每層3—4cm。
                  If the depth of pavement groove is greater than 7 cm, it should be filled in layers and compacted layer by layer, with 3-4 cm per layer.
                  壓實
                  compaction
                  鋪設均勻后,根據實地環境,修補面積的大小和深度,選擇適當的壓實工具和方法進行壓實。如汽車輪胎壓實、人力夯、振動平板夯壓實、壓路機壓實。高等級公路修補時,修補區域的四周和邊角應保證充分地壓實。
                  After laying uniformly, according to the field environment, the size and depth of repair area, select ffdiping.37ix.com.cn fddiping.37ix.com.cnwendingji.37ix.com.cnzuranji.37ix.com.cnfangwuji.37ix.com.cn guangliangj.37ix.com.cnappropriate compaction tools and methods for compaction. Such as automobile tire compaction, manpower compaction, vibration plate compaction, roller compaction. When repairing high-grade highway, the surrounding and corner of repairing area should be fully compacted.
                  開放交通
                  Open traffic
                  冷補工藝操作時間短,修補10分鐘后即可直接通車
                  Cold repair process operation time is short, repair 10 minutes can be directly opened to traffic

                  北京鼎锘恒潤建筑裝飾有限公司

                  1. 電話:13313028229
                  2. 網址:www.www.jiamusidaxue.com

                  版權北京建筑裝飾有限公司 網址:www.www.jiamusidaxue.com 推薦:北京鋼結構加建閣樓制作,北京別墅加建改造公司,北京現澆混泥土澆筑公司,北京路面切割修復公司,北京樓頂防水堵漏公司,北京陽光房制作公司,北京混泥土切割拆除加固,北京現澆混凝土樓板制作公司,北京現澆樓梯公司

                   

                  狠狠综合久久久久精品网站